- 欢迎访问起航教学!
升级路由器 IOS方法总结
12-14 18:36:14 分类:网络硬件 浏览次数: 959次
标签:网络硬件大全,http://www.qihang56.com
升级路由器 IOS方法总结,
reset system reset
set display the monitor variables
stack produce a stack trace
www.qihang56.com
sync write monitor environment to NVRAM
sysret print out info from last system return
tftpdnld tftp image download
unalias unset an alias
unset unset a monitor variable
xmodem x/ymodem image download
rommon 2 〉
在rommon 1〉状态下有两种升级IOS方法。
(一)、通过Xmodem命令(注:Xmodem与实际的modem没有任何联系 只是一个传输协议 数据是通过终端的串口和路由器的Console口灌进去的)升级IOS,具体步骤如下:
1、用Cisco原配的线缆连接路由器的console口与PC机的COM1,使用PC机的超级终端软件访问路由器,这时不需要对PC和路由器配置任何地址。
2、在这个模式下,输入Xmodem命令,即:
rommon 2 〉 xmodem -c c2600-i-mz.122-11.bin
(-c是带校验,c2600-i-mz.122-11.bin为存放在PC机上的IOS映像文件)
WARNING: All existing data in bootflash will be lost!
Invoke this application only for disaster recovery.
Do you wish to continue? y/n [n]: y
Ready to receive file c2600-i-mz.122-11.bin ...此时在超级终端的传送栏目=〉 选择发送文件选项 =〉 再选择Xmodem 并指明IOS映像文件所在的路径,按发送即开始上传IOS,等待时间很长,视IOS的大小和传输速度。)
Erasing flash at 0x607c0000
program flash location 0x605b0000
Download Complete!
传完以后,对整个系统初始化 显示如下:
program load complete, entry point: 0x80008000, size: 0x5b85e0
Self decompressing the image : #################################################
################################################# [OK]
Smart Init is disabled. IOMEM set to: 10
www.qihang56.com Using iomem percentage: 10
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-I-M), Version 12.2(11)T9, RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 1986-2003 by cisco Systems, Inc.
Compiled Mon 23-Jun-03 15:42 by cmong
Image text-base: 0x8000809C, data-base: 0x80A68B48
cisco 2610 (MPC860) processor (revision 0x203) with 22528K/2048K bytes of memory
Processor board ID JAD03483395 (1128032249)
M860 processor: part number 0, mask 49
Bridging software.
X.25 software, Version 3.0.0.
1 Ethernet/IEEE 802.3 interface(s)
2 Serial(sync/async) network interface(s)
32K bytes of non-volatile configuration memory.
8192K bytes of processor board System flash (Read/Write)
Press RETURN to get started!
*Mar 1 00:00:05.652: %PA-2-UNDEFPA: Undefined Port Adaptor type 100 in bay 1
*Mar 1 00:00:07.996: %LINK-3-UPDOWN: Interface Ethernet0/0, changed state to up
*Mar 1 00:00:07.996: %LINK-3-UPDOWN: Interface Serial0/0, changed state to down
*Mar 1 00:00:07.996: %LINK-3-UPDOWN: Interface Serial0/1, changed state to down
*Mar 1 00:00:09.142: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0/0, changed state to up
*Mar 1 00:00:09.142: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, changed state to down
www.qihang56.com
*Mar 1 00:00:09.142: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/1, changed state to down
*Mar 1 00:00:09.458: %SYS-5-CONFIG_I: Configured from memory by console
*Mar 1 00:00:11.245: %LINK-5-CHANGED: Interface Serial0/1, changed state to administratively down
*Mar 1 00:00:12.275: %SYS-5-RESTART: System restarted --Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-I-M), Version 12.2(11)T9, RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 1986-2003 by cisco Systems, Inc.
Compiled Mon 23-Jun-03 15:42 by cmong
*Mar 1 00:00:12.279: %SNMP-5-COLDSTART: SNMP agent on host NE16 is undergoing a cold start
Router〉
采用这种方法时,由于使用console口来传送,速率为9600bps,需要时间较长。因此可修改console口速率利用xmodem命令实现快速升级IOS。具体方法如下:
rommon 1 〉 confreg 回车
Configuration Summary
enabled are:
load rom after netboot fails
console baud: 9600
boot: image specified by the boot system commands
or default to: cisco2-C2600
do you wish to change the configuration? y/n [n]: y (选择 yes)
enable “diagnostic mode“? y/n [n]: n (选择 no)
enable “use net in IP bcast address“? y/n [n]: n (选择 no)
disable “load rom after netboot fails“? y/n [n]: n (选择 no)
enable “use all zero broadcast“? y/n [n]: n (选择 no)
enable “break/abort has effect“? y/n [n]: n (选择 no)
enable “ignore system config info“? y/n [n]: n (选择 no)
change console baud rate? y/n [n]: y (选择 yes)
enter rate: 0 = 9600, 1 = 4800, 2 = 1200, 3 = 2400
reset system reset
set display the monitor variables
stack produce a stack trace
www.qihang56.com
sync write monitor environment to NVRAM
sysret print out info from last system return
tftpdnld tftp image download
unalias unset an alias
unset unset a monitor variable
xmodem x/ymodem image download
rommon 2 〉
在rommon 1〉状态下有两种升级IOS方法。
(一)、通过Xmodem命令(注:Xmodem与实际的modem没有任何联系 只是一个传输协议 数据是通过终端的串口和路由器的Console口灌进去的)升级IOS,具体步骤如下:
1、用Cisco原配的线缆连接路由器的console口与PC机的COM1,使用PC机的超级终端软件访问路由器,这时不需要对PC和路由器配置任何地址。
2、在这个模式下,输入Xmodem命令,即:
rommon 2 〉 xmodem -c c2600-i-mz.122-11.bin
(-c是带校验,c2600-i-mz.122-11.bin为存放在PC机上的IOS映像文件)
WARNING: All existing data in bootflash will be lost!
Invoke this application only for disaster recovery.
Do you wish to continue? y/n [n]: y
Ready to receive file c2600-i-mz.122-11.bin ...此时在超级终端的传送栏目=〉 选择发送文件选项 =〉 再选择Xmodem 并指明IOS映像文件所在的路径,按发送即开始上传IOS,等待时间很长,视IOS的大小和传输速度。)
Erasing flash at 0x607c0000
program flash location 0x605b0000
Download Complete!
传完以后,对整个系统初始化 显示如下:
program load complete, entry point: 0x80008000, size: 0x5b85e0
Self decompressing the image : #################################################
################################################# [OK]
Smart Init is disabled. IOMEM set to: 10
www.qihang56.com Using iomem percentage: 10
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-I-M), Version 12.2(11)T9, RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 1986-2003 by cisco Systems, Inc.
Compiled Mon 23-Jun-03 15:42 by cmong
Image text-base: 0x8000809C, data-base: 0x80A68B48
cisco 2610 (MPC860) processor (revision 0x203) with 22528K/2048K bytes of memory
Processor board ID JAD03483395 (1128032249)
M860 processor: part number 0, mask 49
Bridging software.
X.25 software, Version 3.0.0.
1 Ethernet/IEEE 802.3 interface(s)
2 Serial(sync/async) network interface(s)
32K bytes of non-volatile configuration memory.
8192K bytes of processor board System flash (Read/Write)
Press RETURN to get started!
*Mar 1 00:00:05.652: %PA-2-UNDEFPA: Undefined Port Adaptor type 100 in bay 1
*Mar 1 00:00:07.996: %LINK-3-UPDOWN: Interface Ethernet0/0, changed state to up
*Mar 1 00:00:07.996: %LINK-3-UPDOWN: Interface Serial0/0, changed state to down
*Mar 1 00:00:07.996: %LINK-3-UPDOWN: Interface Serial0/1, changed state to down
*Mar 1 00:00:09.142: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0/0, changed state to up
*Mar 1 00:00:09.142: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, changed state to down
www.qihang56.com
*Mar 1 00:00:09.142: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/1, changed state to down
*Mar 1 00:00:09.458: %SYS-5-CONFIG_I: Configured from memory by console
*Mar 1 00:00:11.245: %LINK-5-CHANGED: Interface Serial0/1, changed state to administratively down
*Mar 1 00:00:12.275: %SYS-5-RESTART: System restarted --Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-I-M), Version 12.2(11)T9, RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 1986-2003 by cisco Systems, Inc.
Compiled Mon 23-Jun-03 15:42 by cmong
*Mar 1 00:00:12.279: %SNMP-5-COLDSTART: SNMP agent on host NE16 is undergoing a cold start
Router〉
采用这种方法时,由于使用console口来传送,速率为9600bps,需要时间较长。因此可修改console口速率利用xmodem命令实现快速升级IOS。具体方法如下:
rommon 1 〉 confreg 回车
Configuration Summary
enabled are:
load rom after netboot fails
console baud: 9600
boot: image specified by the boot system commands
or default to: cisco2-C2600
do you wish to change the configuration? y/n [n]: y (选择 yes)
enable “diagnostic mode“? y/n [n]: n (选择 no)
enable “use net in IP bcast address“? y/n [n]: n (选择 no)
disable “load rom after netboot fails“? y/n [n]: n (选择 no)
enable “use all zero broadcast“? y/n [n]: n (选择 no)
enable “break/abort has effect“? y/n [n]: n (选择 no)
enable “ignore system config info“? y/n [n]: n (选择 no)
change console baud rate? y/n [n]: y (选择 yes)
enter rate: 0 = 9600, 1 = 4800, 2 = 1200, 3 = 2400
相关热词搜索:
- ·上一篇:内存的选购与注意事项
- ·下一篇:新手怎样卸载残留组件
分享到:
收藏
评论排行
网络硬件 热门排行
- · 关于局域网中共享的几个小技巧 -[组网
- · Windows XP共享经典问题详细拆解 -[组
- · 路由器设定来控制带宽流量占用
- · 网线信号衰减问题怎么解决 -[域网维护
- · ADSL数据分包功能设置
- · 路由器网络故障诊断分步骤解析
- · 交换机初始设置
- · 硬盘故障代码你都懂吗
- · 升级路由器 IOS方法总结
- · 安全有效的配置无线局域网络
- · 硬件冲突导致Windows 7系统无线路由器
- · 路由器安全使用技巧的十大箴言
- · 全面解决无线路由器无法上网的问题
- · 怎样让你的猫跑的更快更稳
- · 双网卡冲突如何解决
- · 对于无线路由自动掉线巧解决
- · 网络通信-轻松修改网卡MAC地址
- · 无线网络连接故障的12个解决方法
- · 电脑超频后网卡故障解决
- · MODEM不执行拨号操作的原因及处理办法
- · 安装网卡驱动以后无法上网的解决办法
- · 交换机端口“假死” 的处理方法 -[网络
- · 交换机速度升级时的注意事项
- · 家庭组网 ADSL如何通过硬件来共享上网